基于虚拟样机技术的航空发动机放气活门机构仿真及故障分析

针对某型航空发动机放气活门机构主动摇臂的多起断裂故障,为寻找故障原因并尽可能缩短排故周期与降低排故成本.借助虚拟样机技术建立此机构的动力学仿真模型,利用动力学仿真软件ADAMS与有限元分析软件ANSYS的联合仿真分析,实现放气活门机构摇臂断裂故障再现,并找出断裂件受力的主要影响因素及其影响规律,估算各受力水平下断裂摇臂的疲劳寿命.最终,分别给出保证摇臂最低使用寿命与全寿命使用情况下的改进建议,即将摇臂与放气活门之间间隙B增大至0.273mm与0.279mm,从而为实际工程排故提供理论依据.      

U型节流槽等压差活门内流场特性

以某U型节流槽等压差活门为研究对象,开展了内流场性能数值模拟研究.基于三维建模造型技术对所设计的压差活门进行初步建模,然后采用周期性网格网格单元划分等压差活门的结构化网格;进而通过CFD数值模拟进行了内流场仿真分析,并对不同出口节流开度的等压 差活门模型进行了对比研究.内流场状态表明:U型节流槽等压差活门不同流量以及不同出口节流开度下在节流口处由于面积突变,压力梯度变化较大,等压差活门的压降主要集中在此处,且均存在一定范围低速团与二次旋涡流等.仿真结果预测的外特性性能表明:等压差活门的压差在不同流量工况下和相同流量的不同出口节流开度下,压差维持在0.9MPa左右,符合设计要求.且不同出口节流开度下压差变化趋势相似,出口节流开度越大,压差越大,小流量下相应更快.      

C/SiC复合材料紧固件拉-拉疲劳行为研究

为了研究C/SiC复合材料紧固件的拉-拉疲劳行为,在疲劳应力比为0. 1、加载频率为10 Hz的条件下对不同应力水平的疲劳寿命进行统计。采用断口分析和金相分析方法对C/SiC复合材料螺钉疲劳破坏的细观机制进行了研究。结果表明:C/SiC复合材料螺钉拉-拉疲劳包含拉断疲劳及拉脱疲劳两种失效形式;基于双参数幂指数形式的寿命模型,两种失效形式的疲劳寿命经验公式相似;C/SiC复合材料螺钉的疲劳极限约为拉伸强度的65%～70%,若最大疲劳应力大于0. 7σmax,其材料损伤随循环次数增多而明显增大。     

基于地外天体起飞的真空羽流导流技术仿真与试验研究

针对着航天器发动机羽流导流问题,基于工程经验提出了四种典型导流装置型面(包含内凹槽形式和导流锥形式等),利用计算流体动力学/直接模拟蒙特卡罗(CFD/DSMC)耦合方法,对起飞过程中羽流导流带来的气动力和气动热效应进行了数值模拟,并对不同导流装置情况下羽流场激波、航天器表面压强和热流密度分布规律进行了分析,给出了四种导流装置的导流效果评价。最后以导流锥形式开展试验,对仿真算法进行了验证。结果表明：羽流导流并没有导致发动机燃烧不稳定;综合考虑航天器羽流和发动机安全性,大导流锥导流的方案最优;在导流锥附近的激波位置及形态和仿真一致,仿真与试验的变化趋势一致,仿真算法可信,数据规律可以作为工程参考。     

活门型孔“化方为圆”算法

通过对航空发动机控制系统活门型孔的流量系数稳定性控制的方法进行研究,提出了一套能够将方形活门型孔转化为有规律排列组合小圆孔的算法,并通过实例验证了算法的正确性,同时转化误差小于0.7%,基本实现了工程意义上的等流量系数。该算法将加工工艺性差且计量精度低的方形活门型孔转化为有规律排列组合小圆孔,消除了方形型孔流量系数变化的影响,改变了活门型孔加工方法,减少了对人和环境的危害,提高了活门型孔的计量精度,减小了活门的液动力,具有极大的工程应用价值。 该算法可以实现将方形、梯形（含三角形）及其组合型孔等任意型孔的转化,具有工程上的普遍适用性。     

Experimental investigations of the spray structure and interactions between sectors of a double-swirl low-emission combustor

In this paper, the spray characteristics of a double-swirl low-emission combustor are analyzed by using Particle Imaging Velocimetry (PIV) and Planar Laser Induced Fluorescence (PLIF) technologies in an optical three-sector combustor test rig. Interactions between sectors and the influence of main stage swirl intensity on spray structure are explained. The results illustrate that the swirl intensity has great effect on the flow field and spray structure. The spray cone angle is bigger when the swirl number is 0.7, 0.9 than that when the swirl number is 0.5. The fuel distribution zone is larger and the distribution is more uniform when the swirl number is 0.5. The fuel concentration in the center area of the center plane of side sector (Plane 5) is larger than that of the center plane of middle sector (Plane 1). The spray cone angle in Plane 5 is larger than that in Plane 1. The width of spray cone becomes larger with the increase of Fuel–Air Ratio (FAR), whereas the spray cone angle under different fuel–air ratios are absolutely the same. The results of the mechanism of spray organization in this study can be used to support the design of new low-emission combustor.     

Optimization and verification of free flight separation similarity law in high-speed wind tunnel

Based on the similarity of separation time, a similarity law optimization method for high-speed weapon delivery test is derived. The typical separation state under wind load is simulated by the numerical method. The real separation data of aircraft, separation data of previous test methods, separation data of ideal wind tunnel test of previous methods, and simulation data of the proposed optimization method are obtained. A comparison of the data shows that the method proposed can improve the performance of tracking. Similarity law optimization starts with the development of motion equations and dynamic equations in the windless state to address the problems of mismatching between vertical and horizontal displacement, and to address the problems of separation trajectory distortion caused by insufficient gravity acceleration of the scaling model of existing light model. The ejection velocity of the model is taken as a factor/vector, and is adjusted reasonably to compensate the linear displacement insufficiency caused by the insufficient vertical acceleration of the light model method, so as to ensure the matching of the vertical and horizontal displacement of the projectile, and to improve the consistency between the test results of high-speed projection and the actual separation trajectory. The optimized similarity law is applicable to many existing free-throwing modes of high-speed wind tunnels. The optimized similarity law is not affected by the ejection velocity and hanging mode of the projectile. The optimized similarity law is suitable not only for the launching of the buried ammunition compartment and external stores, but also for the test design of projectile launching and gravity separation.     

橡胶减振垫在航天器中的应用及验证

文章针对某航天器振动试验过程中出现的自锁阀及其安装支架振动响应放大问题,提出了一种采用橡胶减振垫的解决措施,给出了增加减振垫后设备安装的刚度模型及其分析,并通过振动试验验证了这种方法的有效性。试验结果表明:采用橡胶减振垫可以较好地解决部分航天器上仪器设备在振动环境条件下响应超标的问题,措施简单有效,满足使用要求,具有一定的推广应用价值。     

气动换向阀阀芯/阀座撞击特性研究

针对某型气动换向阀在研制过程中出现由于阀芯/阀座撞击变形导致阀芯卡死的现象,对阀芯/阀座的撞击特性进行了仿真研究,定量分析了撞击过程以及不同阀座高度对撞击特性的影响,根据仿真结果对换向阀进行了改进设计,试验结果表明改进后的换向阀满足使用要求.     

高压气动电磁阀可靠性改进设计

高压气动电磁阀是地面供气系统使用的关键元件,其可靠性直接关系到运载火箭能否正常完成发射流程。本文对高压气动电磁阀的故障模式进行分析,并对其可靠性改进设计、可靠性试验以及可靠性评估等技术进行了介绍,通过一系列可靠性改进设计及验证试验工作,使高压气动电磁阀可靠性有所增长,并在大型飞行试验中得到验证。